Search results

Edited as incorrectly sent.

As mentioned in another post this morning I am about or rather have started a new build on a Peugeot Boxer, as I promised Millie here are a few photos of the start. First few are some of the goodies to go in, I'm doing something different on this one I'm fitting full privacy glass sides and...

Sorry for late reply Robbo, been working on the van all day. No just dot and dab here a d there, never had a problem with condensation, but then once the insulation is on I'm not going to rip it off to find out 😆. My van was done 7 years ago and been all over the continent and as far as I'm...

Will do Phil, I'll post some picture today as for the start of the build, I've just ti's minute swapped the vans around so as I can start on my sister in laws. Phil

I personally have never had problems sticking Celotex or Retinol to any surface with an adhesive sealant like "Sticks like shit" or as Millie suggested "Stixall". And have never had to clean the foil for it to bond to the point where it would destroy the sheet if it had to be removed. P.s. I've...

Galvanising has always only been a zinc coating of iron or steel Dave, the main differences is how it is applied electrolysis or hot dipped. Galvanised steel is usually guaranteed for 20 years against rust if its done properly of course. Phil P.s. You have to be very careful when welding...

As Millie after 5 years my rear siez roof light started leaking in the o/s rear corner where water builds in the roof corrugation. We were away when it started but I had my "Sticks like shit" and gun with us so I stuck my head above the open light dried the area along the back and plastered...

About 4 years ago I was reversing in at night beside my shed/workshop and came to a crunching stop, I'd hit the eve of my workshop luckily little damage to the eve of the shed but bent the top righthand rear quarter of the van, not seriously but enought to crinkle the metal work and lose about...

With all due respect to all who advise the non use of ply for floor base, the use of ply has been the main stay of builders professional and self build since ply was in common use in the early 20's. Admittedly the quality of ply is an issue but so long as the build is well administered and the...

This is good advice, I also have 25mm insulation under a 19mm ply floor with Carnian flooring over the ply, and in the depths of winter we can walk bare foot on the floor and not feel the cold. Phil I did at one point put my total build pictures up through photo bucket, but I think they have...

I concur with Squirrell, insulation is key to noise and comfort both cold & heat my view on spray foam from what I have learnt over the years and from honest posts about it from folk who have had it done is, a) it's expensive b) You must find a really competent sprayer of foam c) it's very very...

Ha! see what you mean Dave. I'm talking about rear door windows. Missed the fact that Trucker was talking about rear side windows. Phil

I didn't know that rear tinted windows were unacceptable! I thought they were only interested in the side windows and how many side windows? Phil

I agree, in the past Millie Master and I have had words through emails with the head of DVLA when the rules were announced but not as yet put into practice, it seems as though it was left up to people who had no interest in camper vans or motorhomes to decide if it was going to be reclassified...

Hi Trucking, Yes it has now become very difficult to get it registered as a "Motor caravan". Your other half is correct that the passenger window does not count in the amount of windows required per side, it is two windows on one side and at least one window on the opposite side. Preferably...

Beyond me Trev, haven't sprayed professionally for 25years 😜 but when I do I seem to get a great finish with my trusty old devilbiss. Phil

That was 1978 Trev, that was a top of the range Devilbiss at the time much later I bought top of the range devilbiss gravity fed which I still own and use on occasions 😁. Phil

Just realised, check out the shirt and the collar, just proves its a seventies photo 😂. Phil

Trust me my wife decided to have a clear out today and guess what I came across, this is totally coincidence, this is a picture of me heating up some cellulose paint prior to spraying something or other. So much for health and safety in those days 🤣, however here I am safe and sound at 70 😊...

Thanks, interesting. Yes about 30 years ago I had a drip fed old cast iron waste oil heater that I used in the garage and I remember now it was a sod to light as in the winter the oil was so thick it would not drip fast enough to keep the burn pan alight, so I'd have to light old rags soaked in...