Search results

Most kits come with a tank dipper unit, one that you fit through the tank pick up unit, it's fairly easy to do on a Ducato but I'm not sure about other vehicles. Phil

😄 to the area description 😒 to the water heater problem. Phil

By the way Phil Solva is in West Wales quite a long way from South Wales 😀. South Wales is generally as far as Swansea from Cardiff from Swansea onwards you start to come into West Wales, anything north of Cardiff/Swansea is known as the vallys after the valleys it becomes Mid Wales and finally...

Sprinter is right Phil they are near Blaenavon probably not far from you if your in South Wale. It's called Soth Wales Caravan centre, I bought most of my white goods from them new but very cheap at the time, plus my Truma 4e, but they do rip out Caravans and sell off the innards etc. Best...

Where in Wales are you Phil. Can't help with your heater prob I'm afraid 😕. Phil.

I don't really know for sure Phil, it's been five months already and nearly every week day full time but she uses it on weekends and we go away each weekend too, I'd hazard about a further two or three weeks 😬. Phil

Few more photos of build continuation, finished the door overhead/switch panel trim and hab to cab architecture. Hopefully will start on overhead lockers tomorrow. Phil

Thats a Sietz window Keith, sorry I've been swapping over to a new phone over the last few days, far harder than building a van 😄, only just got the ability to view this site back. Phil

This sort of place and as Dave suggests Magnums would be a good place even if only to ask if they know where you might get one, though I'm doubtful that you will be able to source a new piece as most shops want to only sell the complete window. But the actual manufacturer might possibly send you...

Hmmm, it as Phil (Millie master) says really needs a photo put up of the window in question. I think your talking about the inverted 'U' shaped rail that is clamped to the top of the window and is clipped into the receiver rail that's attached to the window frame, but can not be sure. Some where...

A little more information on exactly what make and type would be helpful 🙂. Phil

Sorry I was assuming you had a panel van conversion but of course your van is a coach built. So no I was suggesting that you went back to a fixed double seat as per the original for a Ducato/Relay/Peugeot van and you would have to leave by the drivers door and walk round to the hab door to get...

Be very careful as double seats are not the same fittings, the swivel base you have located will have a very specific make of seat that corresponds to it, or you will be into a major modification situation 😉. Phil If you intend to go down the three seats in the cab then I would buy the the two...

Further progress on Sis in laws van, doors all on now and started on top lockers, beginning with the Micro wave cupboard.

As promised these are photos of double swivel seat from a VW (Not sure which model) sat on a box framed base that I welded up encased in decorative ply all mounted on front plates over inside floor and rear plates under the floor pan. The seat itself can as seen swivel 180deg and locks into...

I'm here on holiday with him and his family at Llangennith I'll take some photos later when their three year old wakes up from her afternoon knap 😁. Phil P.s. Its actually swivelling so has a 180 deg position though only locks into travelling position at forward and rear ward positions.

Bloody hell Robbo, that is a massive job but the end result looks fab bet your proud of it. We'll done and a great effort 👌. Phil

When you get the bonding kit cut off the spike on the plastic nozzle, hold the gun/nozzle at 90 deg to the bodywork and so that the "V" of the nozzle leaves a high triangle continously around the window aperture, try to complete it in one go, it's very difficult to do it in one go but try to...

You get the primer with the bonding kit along with the application bud on a stick. The primer is also an anti corrosion fluid too. You must follow the instructions that comes with the kit. Phil P.s. The primer can be used on bare metal to stop corrosion.

This is all you will need to bond the window just follow the instructions to the letter. Phil